Protimeter SurveyMaster LE (BLD5364) Non-invasive & Pin Moisture Meter |
Model #: BLD5364
| |
 |
| Quantity Discounts |
| 1 | 2-4 | 5-9 | 10-19 | 20+ |
| $409.00 | $396.73 | $384.46 | $372.19 | $359.92 |
|
|
|
|
|
|
|
Surveymaster LE incorporates two
modes of operation (Search and Measure) that enable the user
to distinguish surface moisture from sub-surface moisture, essential
information when trying to establish the extent and cause of a moisture
problem.
The Search Mode is used to assess the moisture level
beneath the surface of solid walls and floors independently
of surface conditions. The nominal depth of the
measurement is 3/4" (19mm) this depends on the density
and other characteristics of the material. When held
against the surface, as shown below, the instrument
transmits a signal into the material. The relative moisture
level is shown on the digital display and its moisture
condition is shown on the accompanying scale of
color-coded lights. This measurement presentation helps
the user to:
- Look for moisture behind wall and floor coverings,
such as tile and vinyl
- Assess, in relative terms, if the material is in a dry,
borderline or damp condition
- Map the extent of the problem numerically
- Not adversely affected by surface moisture such as condensation
- Non-invasive Pinless radio frequency finds moisture at
depth where moisture is not always directly visible up
to 3/4" (25.4 mm) below the surface
- This mode of measurement is not adversely affected
by the presence of surface moisture
Applications: Shower pans, behind ceramic tile, fine finishes,
water stains, tile and vinyl floor coverings, joists,
around toilets, drywall, below grade floors and walls,
plaster, masonry, concrete and concrete block.
 The
Measure Mode is used to measure the moisture level at the
surface and at incremental depth, when used with the
auxiliary deep wall probes. Measure mode readings are
precise and specific to the immediate area of contact of
the electrodes. The actual moisture content of wood is
shown on the digital display with the corresponding
moisture condition shown on the accompanying scale of
color-coded lights. Wood Moisture Equivalent (WME) values
are shown for other non-conductive, porous building
materials
- Pin-type probes measure moisture in wood and other
building materials (use provided calibration chart for
more precise readings)
- Detects moisture directly in materials and below wall and floor
coverings such as tile, wood and vinyl
- Deep wall probes establish the presence of moisture in
wall cavity insulation, sub and surface structures
- Assess, in relative terms, if the material is in a dry, borderline or damp
condition
Applications: Wood and wood floors, drywall, concrete and concrete block, stucco, plaster, masonry and EIFS.
- Pin measurement moisture range(WME): 7% to 99%
- Max. needle penetration: 0.4" (10mm)
- Non-Invasive (RF) moisture range: 6 to 100% (relative) up to 3/4"(19.05mm) deep
- Resolution: 0.1%
- Power: (1) 9v battery (included)
- Dimensions (L×W×D): 6.8" × 1.2" × 1.9" (175×30×48mm )
- Weight: 3.5 oz (100g)
- Audible alert (may be switched on/off by the user)
- Auto power off (may be switched off, or set between 1-3 minutes, by the user)
- Dual Display LCD and LED
- Digital 60 LED’s Green (“dry”) , Yellow (“at risk”) and Red (“wet”)
- Digital LCD
- Reset reading for sensitivity adjustment
- Hold Feature
Supplied with:
- Carrying Case Pouch with belt loop
- 9v Battery
- Spare Pins & Calibration Check Device
- External (2 pin) standard probe (BLD5079)
- Manufacturer's warranty (2 year parts and labor)
- Instruction Manual & Wood calibration chart -150 commonly used species
Options:
- External (2 pin) heavy duty probe (BLD5060)
- Deep (5") wall probes Plug-in type (BLD5018)
- EIFS* probe
finds moisture in exterior insulation finishing systems (BLD5070)
- Hammer electrode probe for wood floor applications (BLD5050)
*Exterior Insulation and Finished Systems |
|
|
|
|
| Search Category: Hardware > Tools > Measuring Tools & Sensors > Moisture Meters |
|
|
|
|
|
|
|
